Measure / Calibrate: M1

The M1 gauge can replace up to five 0.25% mechanical gauges with an accuracy reading of 0.2%.

Do more with less!  EC Declaration of Conformity DNV Certificate

The M1 is a digital pressure gauge with 0.2% of reading accuracy. It competes directly with mechanical gauges. Accuracy is not degraded by dropping, over-pressure, rapid pressure changes or temperatures between -10˚C and 50˚C.

One M1 gauge can replace up to five 0.25% mechanical gauges with an accuracy reading of 0.2%.

  • Enclosure is rated to NEMA 4, IP65
  • Can be customized for specific vendor applications
  • Battery life up to 3 years continuous use
  • Bright backlit display
  • G ¼ B BSP parallel fittings available
  • Protective boot included

360 View Request More Info

Applications

  • Replaces ruggedized 0.25% mechanical gauges         
  • Basic digital pressure gauge  

Included with every new M1 Digital Pressure Gauge is an A2LA accredited calibration certificate with test data recorded at 5 different temperatures - proving that it meets published specifications over the entire operating range. You won't get this kind of detailed report anywhere else!


Specifications

Specifications include all effects of linearity, hysteresis, repeatability, temperature, and stability for one year.

Accuracy
20% to 100% of Full Scale: ±(0.2% of Reading).
0 to 20% of Full Scale: ±(0.04% of Full Scale).
Vacuum, for 2MPa (300 PSI, 20 bar, 20kg/cm2) and lower pressure gauges:
0 to -99.9 kPa (-14.5 PSIG): ±(0.25% of Full Scale), where F.S.: -99.9 kPa (-14.5 PSIG).
(Not recommended for continuous use at high vacuum.)

Overscale Limit 
Display will flash at 110% of Full Scale.

Pressure Ranges
(see table below for details)

Temperature
Operating & Compensated: -10°C to 50°C (14°F to 122°F).
Storage: -40°C to 75°C (-40°F to 167°F).

Backlit Display
Description: 5 Full (seven segment) digits.
Display rate: 4 readings per second.
Numeral display height: 16.8mm (0.66") single line display. 

Connections
Connections options for the M1 gauge
Pressure connection: 1/4 male NPT or G 1/4 B BSP.

Certifications 
EC Declaration of Conformity DNV Certificate

Media Compatibility
Liquids and gases compatible with 316 stainless steel.

Power
Battery: Two size AA (LR6) batteries.
Battery life: 900 hours at 4 readings/second.
Extended battery life:
1 reading/15 seconds . . . 3,000 hours
1 reading/30 seconds . . . 6,000 hours
1 reading/1 minute. . . . . . 10,000 hours
1 reading/5 minutes. . . . . 25,000 hours
1 reading/10 minutes. . . . 30,000 hours

Enclosure
Description: Water resistant housing incorporating o-ring seals. Polyester/Polycarbonate blend compatible with common industrial fluids, including Skydrol.
Dimensions: 44mm (1.72") D x 108mm (4.25") W x 129mm (5.1") L
Weight: 325g (11.5 oz.), including batteries and protective boot.

Sensor
Piezoresistive silicon sensor with permanent oil isolation system and integral filter. 316 stainless steel welded (not brazed) sensor. No o-rings, thread tape, epoxy or sealant on any part of sensor assembly. 

Additional Features
Vertical bar graph 
Minimum (LO) & Maximum (HI) capture 
Averaging (2 to 20 samples)

Pressure Ranges

PSI1 Pa2 bar1 kg/cm2 1   Pressure Units and Resolution
P/N
Prefix
P/N
Prefix
P/N
Prefix
P/N
Prefix
Over
pressure
PSI kPa MPa bar mbar kg/cm2

inch H20

inch Hg mm H20 mm Hg
30PSI
200KPA
2BAR
2KG
3.0x
0.001
0.01
 
0.0001
0.1
0.0001
0.1
0.01
1
0.1
100PSI
1MPA
10BAR
10KG
2.0x
40.01
0.1
0.0001
0.001
1
0.001
50.1
0.01
 
1
300PSI
2MPA
20BAR
20KG
2.0x
0.01
0.1
0.0001
0.001
1
0.001
 
0.1
 
1
1KPSI
10MPA
100BAR
100KG
2.0x
0.1
1
0.001
0.01
 
0.01
 
0.1
 
 
3KPSI
20MPA
200BAR
200KG
1.5x
0.1
1
0.001
0.01
 
0.01
 
1
 
 
10KPSI
70MPA
700BAR
700KG
1.5x
1
 
0.01
0.1
 
1
 
1
 
 

1 - PSI, BAR, and KG versions can display all available pressure units
2 - KPA/MPA versions can display pressure in kPa, MPa, bar and mbar only
3 - Density of water can be set to 4° C, 60°F or 20°C / 68°F with the keypad
4 - Applies to 100PSI gauge. 1MPA, 10BAR and 10KG units will be 0.1 PSI
5 - Disabled for 1MPA, 10BAR and 10KG units


Options

Part No.

 
-O

Cleaned for Oxygen Service

-BSP

G 1/4 B BSP parallel fitting (Not available for psi models)

3504

G 1/4 B BSP parallel fitting copper washer


Product Downloads

Our Products

Measure
nVision | 30 Series | XP2i-DP | M1 | MultiCal | XP2i | WT Series

Calibrate
nVision | 30 Series | M1 | CrystalCalXP | FastCalXP | Calibration Kits | XP2i

Record
nVision | DataLoggerXP

Systemize
CrystalCalXP | Calibration Kits

Configure
ConFigXP | ConFigM30

Generate
GaugeCalXP | HydraulicPump | ComboPump

Connect
CPF Hose and Fittings

Obsolete Products
Obsolete Products